D4i LED Driver Selection Pitfall | Do NOT Use D4i LED Drivers Under This Condition!
We recently received an enquiry from a client undertaking a large‑scale commercial lighting project, who intended to purchase Lifud D4i LED drivers.
After in‑depth technical communication, however, we found the client only required the data feedback functionality of DALI Parts 251‑253, instead of the full capabilities of D4i. Following our technical review, the project adopted Lifud’s 35mm cutout series DALI‑2 LED drivers together with a small quantity of our 22mm ultra-thin BCD series D4i LED drivers. This configuration not only perfectly matched their requirements but also eliminated the risk of on-site commissioning failures.
Many lighting engineers and solution providers easily fall into the same trap of believing that having DALI Parts 251-253 data feedback means having a D4i LED driver. We’ve previously shared a dedicated article on the differences between DALI, DALI-2, and D4i—those who haven’t read it yet can click the link below to review. Today, we’ll break down this common pitfall once again to help you avoid it during the solution selection stage.
▼ Differences between DALI, DALI-2, and D4i
The Core of D4i: More Than Just Data Feedback, Bus Power Supply Is Mandatory
D4i is built as an extension of DALI-2. DALI Parts 251-253 are indeed mandatory capabilities of a D4i LED driver. But many people only remember the data feedback aspect and overlook the most critical requirement: a D4i LED driver must come with an integrated DALI bus power supply (DALI Part 250). A device cannot be defined as a D4i LED driver without built-in bus power supply.
▼ Lifud D4i LED driver solutions: for outdoor street, industrial lighting, indoor lighting, etc.

Here’s the Problem: D4i’s Bus Function Inherently Conflicts with Large DALI Systems
The built-in bus power supply of a D4i LED driver is required by standard to output ≥50 mA and ≤62.5 mA, and is enabled by default. Meanwhile, the DALI standard requires that total bus current must be ≤250 mA. Once this limit is exceeded, system faults will occur; devices cannot be discovered, and control over the entire DALI loop will fail.
▼ Original text of DALI technical standard
①Scenario 1: D4i bus power supply is enabled by default
Each D4i LED driver supplies only a modest bus current, yet the total adds up quickly when multiple units share one DALI loop. 4 D4i LED drivers on the same loop will push total bus current close to the 250mA upper threshold. Adding a 5th D4i LED driver will push bus current over the limit and trigger system errors. Technicians then have to diagnose each unit one by one.
More importantly, centralized large‑size DALI systems are normally fitted with an external dedicated DALI bus power supply. Even fewer than four D4i LED drivers may overload the bus and trigger system errors.

② Scenario 2: D4i bus power supply is manually disabled
Here, the D4i bus function serves no purpose at all—you need to add and enable a standard DALI bus power in the system before it can be used. And if you later want to turn on the bus function of those D4i LED drivers, you can only do it one by one. Otherwise, they’ll conflict with the system’s bus power supply, trigger system errors, and result in system faults and time‑consuming on‑site troubleshooting.

This pitfall is extremely common in application projects where the team isn’t familiar with D4i functionality. Centralized DALI systems for indoor commercial and office lighting are generally not suitable for mass deployment of D4i LED drivers.
Critical Selection Checklist: What Do You Actually Need?
Ask yourself two questions before selecting LED drivers:
1. Do you need independent single-luminaire control using self-contained bus power supply? If so, go with a D4i LED driver.
2. Or do you simply need data feedback (luminaire/energy/diagnostic data) that will eventually be reported to a large DALI system? Then what you need is just a DALI-2 LED driver with DALI Parts 251-253 functionality.
Both can deliver data reporting, but they are designed for fundamentally different purposes.
In one sentence: D4i LED driver—integrated bus power supply, capable of directly powering sensor modules; standard DALI LED driver—requires external bus power supply, ideal for centralized system control.

Need Driver, Choose Lifud
From LED drivers for outdoor street lighting to those for indoor commercial and office lighting—downlights, spotlights, linear lights—Lifud offers both D4i versions and DALI-2 versions with DALI Parts 251-253 functionality. Different solutions, each tailored to give your smart lighting project the best fit.
For specific details, feel free to reach out.

Previous article
