RDP301-11K Mode 2 EV Charging Main Control Board

Model

RDP301-11K

Parameters

Operating voltage: 400Vac

Output power: 11kW Max.

Output current: 16A Max.

Features

— Adjustable/customizable output current

— All-around protection: OTP/OCP/OVP/UVP/surge protection

— Wi-Fi/Bluetooth interfaces reserved

— Input plug over-temperature protection interface reserved

— High-performance MCU & optimized operating logic

— RCD Type A+DC6mA

— Meets EU & China GB standards

— Compatible with 3-phase input and L1/N/PE 1-phase input working modes

Certifications

CE

Applications

GB mode 2 EV chargers, IEC mode 2 EV chargers

Subject to change without notice. Errors and omissions excepted. Always make sure to use the most recent release.

Keywords:

Category:

Products

EV charger control board

RDP301-11K Mode 2 EV Charging Main Control Board

产品描述
Parameter
Data Sheet

Model

RDP301-11K

Parameters

Operating voltage: 400Vac

Output power: 11kW Max.

Output current: 16A Max.

Features

— Adjustable/customizable output current

— All-around protection: OTP/OCP/OVP/UVP/surge protection

— Wi-Fi/Bluetooth interfaces reserved

— Input plug over-temperature protection interface reserved

— High-performance MCU & optimized operating logic

— RCD Type A+DC6mA

— Meets EU & China GB standards

— Compatible with 3-phase input and L1/N/PE 1-phase input working modes

Certifications

CE

Applications

GB mode 2 EV chargers, IEC mode 2 EV chargers

Subject to change without notice. Errors and omissions excepted. Always make sure to use the most recent release.

Electrical data
Input voltage	1-phase: 230V 3-phase: 400V		Limit 170-270V; Protection is implemented beyond this range
Input frequency	50/60Hz
Output voltage	1-phase: 230V 3-phase: 400V
Output current	16A max.		6A-16A adjustable
Output power	11kW max.		Adjust the power according to the current
Stand-by power consumption	＜5W		Power in non-charging state
Man-machine interaction
Communication mode	Serial digital interface		Mainly used for external WIFI/Bluetooth modules
Man-machine interaction	Screen/indicator light/key interface		Used with RDC201-02
Charger-enable	Plug & charge		The charging logic can be adjusted via software
Operating conditions
Ambient temperature range	-30℃～+50℃		Ultimate temperature for the test of the matching housing (relay Tc<110℃)
Temperature range at storage	-40℃～+85℃
Humidity during operation	5%-95%, no condensation
Operating altitude	< 3000m
Dimensions
Size	1607429.5mm
Installation method	Mode 2
Product weight	180g
Protection
Leakage	Type A+DC6mA
Surge	L-N: ±2000V L/N-PE: ±4000V
Ground	With ground protection function		The screen displays the corresponding fault, and the emergency charging state is entered through manual control. Re-powering on can restore the error report
Overcurrent	>current value set +2A
Overvoltage	Input voltage≥270Vac		If 270Vac is maintained for 2 seconds, an alarm will be triggered and the relay will be disconnected immediately. Normal operation is restored until the voltage is identified to be less than 260Vac for 2 consecutive seconds
Undervoltage	Input voltage≤170Vac		If 170Vac is maintained for 2 seconds, an alarm will be triggered and the relay will be disconnected immediately. Normal operation is restored until the voltage is identified to be greater than 180Vac for 2 consecutive seconds
Plug over-temperature	NTC temp. >70℃		Turn off the output
Relay welding	Relay welding		The screen displays the corresponding fault
Emergency plug disconnection			Return to standby mode after emergency disconnection
Safety & certification
Insulating strength	Input L&N-PE Output L&N-PE Input L&N-CP	AC:2U+1200V 60S, ＜20mA	During testing, the test sample must not exhibit insulation breakdown or arcing phenomena at any test point
Insulation resistance	Input L&N-PE Output L&N-PE Input L&N-CP	DC: 500V， 60S, ＞5MΩ	Test after short-circuiting the input L and N, as well as the output L and N respectively
Certification	CE		Complete system testing
Note: The voltage and current accuracy is ±5%